Yanhua Digimaster 3 User Manual: Installation, Activation, Update

 This article is available with Digimaster 3 odometer correction tool user manual including:

Software Installation

-Install the D3 tool

-Connect the D3 with PC and internet

-Remote Assistance

-Kernel renovation

Software Activation
Software Upgrade

In detail…

Software Installation

1.Install D3 tool

Step 1: Double-click the installation files in the CD

Step 2: Choose the route of Installation

Step 3: Open the software interface as below after installation

2.Connect the D3 with PC and internet

Step 1: Connect the D3 USB with PC

Click "Cancel" after the window bombed as below

Step 2: Click "OK" to close the bombed warning dialog

Step 3: The following window will appear after successful connecting with the device

Step 4: Just reconnect the USB cable if the USB connecting is cut showed as below a window

Please kindly notice:

Insert the connector of LAN cable into RJ45 LAN connector of D3 to make online update

3.Remote Assistance

The YANHUA engineers will provide you on-line technology support via the internet when you choose the long-distance assistance functions.

Step 1: Please contact the distributor to obtain an IP before the Remote Assistance

Then connect your Digimaster 3 master with the internet

Step 2: Open D3 Tool software to enter "Remote Assistance"

Then select "Require Remote Assistance"

Step 3: Input the obtained IP and click "OK" in the bombed window¡£

4.Kernel renovation

Note: Please don't try easily because Kernel Renovation being hazardous. Normally it is used on the useless because of the loss of the kernel.

Step 1: Click keystroke "8" and "OK" together, then power on

The indication of "Press OK to continue and ESC to cancel" will appear on the screen

Press "OK" into Renovation

Step 2: "Found new hardware" is found in the system when you connect a USB cable with the PC

Step 3: Choose "Install the software automatically", Click "next"

Step 4: Running D3 tool software, choose "KERNEL update"

Step 5: Indication "USB connect successfully" will appear as below after the USB is connected

Step 6: Click "KernelUpdate", choose kernel files, and then click "OK" to start the renovation

Step 7: Several minutes is need for kernel renovation.

It is finished when the indication of "USB connect failed" appear.

Software Activation

This guide helps you checking accessories£¬ complete the activation£¬ authorization and updating.

1.Activation

Digimaster-III needs to be activated online with the Activation code provided by us in the first use.

You can activate and recharge Digimaster-III by the following steps.

Step 1: Power on and connect the D3 with the internet.

The unactivated £DD3 show as below

Click "OK" to start activation

Step 2: Input the validation code in the left dialog

Click "next" to download the update program and management program

Step 3: Activation window will appear after downloading the Management program

Please input your information

Step 4: Enter the activation code and password provided by sales then click "next"

2.Paymemt

Step 1: Recharge dialog will appear after D3 activation in the first use. If no, click "Payment" in the "management center" to start recharging.

Step 2: Input the Recharging code and password provided by the sales

And click "Next"

Step 3: Click "Finish" to finish the recharging after reminding of successful Payment appear

Software Upgrade

Here provides a frequent upgrade of software & hardware program. New vehicle models or amend hole in order to improve the functions of Digimaster-III. Please note the upgrade info on the website http://www.autoemaster.com/en/.

Step 1:

Click "Software upgrade" to find a new upgrade

Input the Validation code in the dialog to start the download and upgrade

Step 2: It will remind you whether you need an adapter to upgrade after the software update

Click "YES" to start the adapter upgrade

Click "NO" to next step (No need to upgrade adapter frequently)

Step 3: Enter the verification code and click “Next”

The D3 will restart automatically after a software upgrade

That’s all. Hope it helps you.

Reproduced from:http://blog.yanhuaacdp.com/yanhua-digimaster-3-user-manual-installation-activation-update/

Can Yanhua Digimaster 3 change mileage for Audi A6 C6 4F 2007?

 This is a question from yanhuaacdp.com customer.

The answer is “Yes”

Yanhua Digimaster 3 has been confirmed that can do Audi A6 C6 4F 2007 2.0TFSI

(VIN: WAUZZZ4F07N0xxxxx) odometer correction via OBD.

Select “A6L-2009” instead of “A6 2004-2008 (4F)” on the page below

It will prompt “(7F11) The service is not supported” if you choose “A6 2004-2008 (4F)”

Another question:

When you do the procedure to adjust mileage, and get the message “GLS is normal, are you sure to adjust?” Just click on “Yes” to continue.

That’s all!

http://www.yanhuaacdp.com/wholesale/digimaster-3-no-token-limitation.html

Source: http://blog.yanhuaacdp.com/can-yanhua-digimaster-3-change-mileage-for-audi-a6-c6-4f-2007/

How to program IC/CPU and decode audio on Digimaster 3?

 Yanhua Digimaster 3 works with various types of adapter you can easily achieve odometer correction, Audio decoding, airbag resetting, engine ECU resetting, IMMO, programming key for Benz & BMW etc. Here share the instructions including:

Files Operation

- IC Programming

- CPU Programming

- Signal Generator

Audio Decoding

-Audio Code Management

-Address Code

In detail…

Files Operation:

In this function, you will see IC programming, CPU programming, Odometer adjusting, Audio decoding. It shows the current data read from the IC by HEX format. You can adjust or save the data in this interface.

HEX address is in the left column. The Data area is in the right column. Data ASCII display is at the bottom when you move the scroll bar.

IC Programming

Step 1: Connect the chip De-solder or link the chip to the OBP adapter according to the instruction

Step 2: Choose the corresponding chip in this interface to begin read or program the chip

CPU Programming

Step 1: Connect the chip De-solder or link the chip to the OBP adapter according to the instruction

Step 2: Choose the corresponding chip in this interface to begin read or program the chip

Signal Generator

The frequency signal generator can generate the specified speed signal, connect to the signal pin in the odometer and then used to run the odometer

Audio Decoding:

When the vehicle audio was power off because of buttery damage, the audio will start the anti-theft system automatically. Digimaster III can calculate the audio code out or initialize it.

Audio Code Management

Step 1: De-solder the corresponding chip according to the software prompts. Click "Next" to begin decoding

Step 2: Please remember the code in the pop-up dialogue box, click"Next", the code was written in the chip

Step 3: Solder the chip back to the board, and then use this new code to decode the audio.

Address Code

These models only need to short-circuit some welding spot to reset the code, the software will give a specific method.

Enjoy!